TR7 Toyota Engine, Calgary Alberta

[Yoke]

If anyone is interested there's a 1980 DHC with the Toyota engine conversion at the Calgary pick a part, you can buy the whole car for $999. There's also a 1975 FHC but it's only for parts... if anyone needs anything let me know I'm going to take the Fiat wheels off it first thing in the morning[:D]

[8]Yoke[}:)]

Can't save them all but I am trying!!!

[rsamis]

Hi Yoke, I'm in Edmonton. I'm looking for a fresh air plenum and a turn signal/ high beam switch. I'd also be interested in the interior door panels if they're biscuit color and in good shape. And what condition is the windshield in? OK, I'd better stop now. Thanks!
Royal

Royal
76 FHC, 4-spd, dual Strombergs

[Rich in Vancouver]

I need a diff or complete rear end for a 4-speed, but I wouldn't ask you to do a dirty job like that!

Cheers,
Richard


1975 TR7 ACL764U

[Yoke]

Rich why didn't you say so I have two sitting in my garage..... I wouldn"t charge you to crate it but shipping might be $$$ due to the odd shape.... I just trying to think if anyone I know is heading that way.....

Rsamis I checked for everything you asked and switches gone.... winshield has a small rock chip in the center and would shatter the minute I tried to pull it out. Door panels are gone sorry. If there's anything else you need let me know I've parted out three 7's in the last couple of years and am waiting for two more to come in. Oh and that fresh air plenum is hard to come by at wreckers keep an eye on ebay they come up quite regularly.


[:D]Yoke[8]

Can't save them all but I am trying!!!

[rsamis]

Thanks for checking Yoke. I'll likely be in Cowtown over the Christmas break, so maybe I can come see what you have on your parts cars then?

Royal
76 FHC, 4-spd, dual Strombergs

[FI Spyder]

If you have a pair of lower control arms I would appreciate. Parts cars are far and few between here on the Island. I would love to get a hold of one but just don't have the space. My control arms are worn oval where they connect to engine crossmember. When I got new ball joints put in they pointed it out. They work but get a little squirrely on violent manuevers. Need to be replaced at some point.

[Yoke]

I'll hunt some down for you.

Yoke

Can't save them all but I am trying!!!

[Rich in Vancouver]

Hi Yoke,
Thanks for that, my rear end (my car's actually[:D]) is making so much noise that it is painful to drive any distance.
If you would be willing to ship by bus that would work well for me, and should keep the price down too. All that they would require is a good wrapping of cardboard, nothing fancy.
Ideally I would like a complete rear end less brakes and backing plates.
Let me know if that would work for you and let me know what you want dollar wise.
you can reach me by e-mail leftent1atshaw.ca

Thanks!
Rich

1975 TR7 ACL764U

[Launie]

Rich, I've got a 4 spd rear end in my yard here in Sooke (Victoria). You can have it for $50 plus shipping. It has 70k on it. I need to remove it, so I'd prefer to take off the whole thing. How quick do you need it? I'm travelling through to Calgary in Jan and could drop it off.
And Yoke, do you have a 3.45 rear end (5 spd)? I could pick it up in Jan when in Calgary.

Launie

[Yoke]

Launie let me take a look around I may just have an extra one somewhere.

[:D]Yoke[8]

Can't save them all but I am trying!!!

[Launie]

Thanks Yoke. I'm doing a 3800 Series II into a '76, and the 3.45 will be the best ratio for driving around here. By the way, are you keeping the side stripes on your car? And orange? I had an orange '76 that I had to send to the scrapyard, but I stripped off everything before it went.

Launie

[Yoke]

[?] You lost me on side stripes [?] And the orange comment??

[}:)]Yoke[8]

Can't save them all but I am trying!!!