Anonymous

Gear lever retainer

Here’s where to discuss anything specific about your standard(ish) car or something that applies to the model in general.
Post Reply
Rich K
Wedge Pilot
Posts: 296
Joined: 08 Aug 2015 18:04
Location: Worcester, United Kingdom

Gear lever retainer

Postby Rich K » 05 Sep 2024 19:56

Hi, just found that the gear lever retainer on the gold convertible has suffered the well known problem of the tab at the rear breaking off. I don’t have a spare so made a repair piece with reinforcing webs and welded it in place. Hopefully will be stronger than the original design.
Attachments
IMG_7329.jpeg
IMG_7329.jpeg (105.49 KiB) Viewed 2105 times
IMG_7328.jpeg
IMG_7328.jpeg (104.1 KiB) Viewed 2105 times
1980 TR7 drophead now repainted and started refitting plus V8 upgrade
1977 TR7 fixedhead awaiting restoration
1981 TR7 drophead bodywork and mechanicals now done, completing trim currently.
Ford Ranger Wildtrak
Jaguar XKR Supercharged
Top
Cobber
TRemendous
Posts: 2486
Joined: 19 Sep 2005 10:03
Location: Australia
Contact:
Contact Cobber

Re: Gear lever retainer

Postby Cobber » 05 Sep 2024 21:32

Looks a good solution, personally I would've brazed it, but the tack welds should do well enough
"Keep calm, relax, take a deep breath, focus on the problem & PULL THE BLOODY TRIGGER"

'80 Triumph TR7.
'97 Ford Falcon Longreach 'S' ute,
'98 MG-F.
'83 Jaguar XJ6 Sovereign S3.
Top
Rich K
Wedge Pilot
Posts: 296
Joined: 08 Aug 2015 18:04
Location: Worcester, United Kingdom

Re: Gear lever retainer

Postby Rich K » 05 Sep 2024 21:43

Thanks Cobber. I agree that brazing might be better but I only have Mig welding kit and haven’t tried to braze anything for decades. The welds seem to have taken ok.
1980 TR7 drophead now repainted and started refitting plus V8 upgrade
1977 TR7 fixedhead awaiting restoration
1981 TR7 drophead bodywork and mechanicals now done, completing trim currently.
Ford Ranger Wildtrak
Jaguar XKR Supercharged
Top
dursleyman
TRiffic
Posts: 1572
Joined: 11 Jun 2007 22:55
Location: United Kingdom
Contact:
Contact dursleyman

Re: Gear lever retainer

Postby dursleyman » 07 Sep 2024 15:26

The guys in the USA have produced an uprated 3D printed one that looks the business. Apparently been extensively tested and a good upgrade.
One of their pictures.
Attachments
IMG_6613.JPG
IMG_6613.JPG (73.97 KiB) Viewed 2023 times
Russ

1981 TR7 Sprint DHC & 1977 TR7 Sprint FHC
Dursley
UK

http://tr7russ.blogspot.co.uk/

Image Image
Top
Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:
Contact Beans

Re: Gear lever retainer

Postby Beans » 08 Sep 2024 18:03

dursleyman wrote:The guys in the USA have produced an uprated 3D printed one that looks the business.

That indeed does look well designed!
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)
http://www.tr7beans.blogspot.com/
Top
Howard_B
Rust Hunter
Posts: 167
Joined: 09 May 2015 16:11

Re: Gear lever retainer

Postby Howard_B » 18 Sep 2024 22:56

I have one and can confirm it looks good, but for various reasons haven't got around to installing it yet
Cheers
Howard
Top
Post Reply

Who is online

Users browsing this forum: No registered users and 170 guests

cron