Anonymous

Suspension turret strengtheners ?

Do you have a question? Ask it here! The reference library for all your DIY instruction guides, aka ‘surely there must be an easier way of doing this’.
Post Reply
tr7dan
Rust Hunter
Posts: 117
Joined: 18 Jun 2009 22:53
Location: United Kingdom
Contact:

Suspension turret strengtheners ?

Postby tr7dan » 28 May 2020 23:11

1980 TR7 DHC

I am just repairing the rusted sides of the front suspension turrets - do I need to renew the two (per side) small angle brackets that join the suspension turret to the inner wing - I've removed them to do the repair but they are such a rust trap ?

Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Suspension turret strengtheners ?

Postby Beans » 29 May 2020 18:35

As far as I know they were only used to ease locating/aligning the inner wings to the body prior to welding.
They are only found on the later Canley and Solihull built cars. Early cars (like this '76 car) didn't have them ...

Image
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

busheytrader
TRemendous
Posts: 3145
Joined: 14 Oct 2007 17:49
Location: United Kingdom
Contact:

Re: Suspension turret strengtheners ?

Postby busheytrader » 29 May 2020 20:56

As if there weren't enough rust traps in the original TR7 design, they added some extra ones? :D

Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Suspension turret strengtheners ?

Postby Beans » 29 May 2020 22:36

busheytrader wrote:As if there weren't enough rust traps in the original TR7 design, they added some extra ones? :D

British engineering at its best :mrgreen:
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

FI Spyder
TRemendous
Posts: 8917
Joined: 03 Jul 2006 19:54
Location: Canada

Re: Suspension turret strengtheners ?

Postby FI Spyder » 30 May 2020 15:37

It was meant to be driven on sunny days, top down, in the desert, in summer where only the occasional shower that popped up would you have to put the top up in a hurry. Of course the hot dry desert sun would quickly dry everything out. The rest of the time it was in the garage. That's were my car spent its first half of its life and there is no rust to prove it. 8)
- - -TR7 Spider - - - 1978 Spitfire- - - - 1976 Spitfire - - 1988 Tercel 4X4 - Kali on Integra - 2013 Volt - Yellow TCT

busheytrader
TRemendous
Posts: 3145
Joined: 14 Oct 2007 17:49
Location: United Kingdom
Contact:

Re: Suspension turret strengtheners ?

Postby busheytrader » 30 May 2020 18:56

I have to raise the top under a bridge to avoid getting soaked if caught out in the rain. It takes forever. Stay above 30mph and the rain goes straight over the top. :D
My manual MX5 hood in comparison can be raised in 5 seconds from the driver's seat.

I recently saw a dry state TR8 being restored in the UK. The restorer searched for rust with an endoscope but found none, even though the sills were barely covered in primer inside.

dursleyman
TRiffic
Posts: 1572
Joined: 11 Jun 2007 22:55
Location: United Kingdom
Contact:

Re: Suspension turret strengtheners ?

Postby dursleyman » 31 May 2020 15:25

I have those on one side of my DHC but not on the other!
Attachments
IMG_5789_500x.jpg
IMG_5789_500x.jpg (80.92 KiB) Viewed 8466 times
Last edited by dursleyman on 08 Jun 2020 14:04, edited 1 time in total.
Russ

1981 TR7 Sprint DHC & 1977 TR7 Sprint FHC
Dursley
UK

http://tr7russ.blogspot.co.uk/

Image Image

Cobber
TRemendous
Posts: 2486
Joined: 19 Sep 2005 10:03
Location: Australia
Contact:

Re: Suspension turret strengtheners ?

Postby Cobber » 01 Jun 2020 08:38

They don't look like they'd do much!
If your at all worried about loosing structural integrity by deleting them, I suggest a strut brace to join the 2 strut towers together would more that compensate.
"Keep calm, relax, take a deep breath, focus on the problem & PULL THE BLOODY TRIGGER"

'80 Triumph TR7.
'97 Ford Falcon Longreach 'S' ute,
'98 MG-F.
'83 Jaguar XJ6 Sovereign S3.

tr7dan
Rust Hunter
Posts: 117
Joined: 18 Jun 2009 22:53
Location: United Kingdom
Contact:

Re: Suspension turret strengtheners ?

Postby tr7dan » 08 Jun 2020 12:38

Ok, thanks for the replies - I've done the repair without refitting them but just got to thinking afterwards if I should have made up some new ones but looks like I don't need to....

Image

Image

Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Suspension turret strengtheners ?

Postby Beans » 08 Jun 2020 18:46

That first picture clearly shows what a rust trap these brackets are :roll:
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

busheytrader
TRemendous
Posts: 3145
Joined: 14 Oct 2007 17:49
Location: United Kingdom
Contact:

Re: Suspension turret strengtheners ?

Postby busheytrader » 09 Jun 2020 10:34

Yes - at 19 years old mine required new metal in the turrets because of them.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests