hood

sonscar · Postby **sonscar** » 12 Jan 2015 15:16

Since fitting a new hood I have tried every possible permutation of folding it,all with varying degrees of success.I undo the velcro over the rail,pull the window back over the boot and that is where it goes wrong.The instructions say fold the side windows in but no matter how I try it seems that the side windows crease as the fixed part at the rear is the same width as the distance between the windows.Any tips?Steve..

]

mine

Beans · Postby **Beans** » 12 Jan 2015 16:23

a quick summary of the official instructions;

Un-do the velcro strip inside the hood (at the top of the roof);
Un-do all poppers (4 per side) and release the header rail;
Fold the hood back onto the boot;
Pull the hood back at the top of the rear screen so the rear window lies flat on the boot;
Fold the side windows over taking care to fold the hood fabric not the plastic windows;
Take hold of the top of the rear screen again and fold it back over the hood stowage area (the side windows will be underneath);
Push flat making sure no plastic windows have been folded & attach hood cover.

I always tuck the front of the folded hood underneath the frame, making sure the windows are not folded.

<center>

1976 TR7 FHC (needs some TLC ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng
[url="http://www.tr7beans.blogspot.com/"]My full Blog[/url]</center>

darrellw · Postby **darrellw** » 12 Jan 2015 16:37

I have the same problem as Steve. I follow the official instructions, but no matter how the side window flaps are folded over, the corners of the side windows get folded a bit. The section of the rear center edge of the hood that is permanently attached is just too wide.

Darrell Walker
66 TR4A IRS-SC CTC67956L
81 TR8 SATPZ458XBA406206
Vancouver, WA, USA

busheytrader · Postby **busheytrader** » 12 Jan 2015 16:56

The best graphic about this is ironically on this website.
http://www.triumphtr7.com/documents/art ... ldroof.asp

I follow the factory / Beans instructions and have no issues. It's possible that aftermarket hoods have slightly different sized clear plastic inserts.

Hope this helps,

Adam

TR7 V8 DHC Jaguar Solent Blue. 9.35cr Range Rover V8, Holley 390cfm, JWR Dual Port, 214 Cam, Lumention, Tubular Manifolds, S/S Single Pipe Exh, 3.08 Rear, 200lb Spax & PolyBushes all round, Anti- Dive, Strut-Top Roller Bearings, Capri Vented Discs & Calipers, Braided Hoses, 4 Speed Rear Cylinders, Uprated Master Cylinder & Servo, AT 14" 5 Spokes or Maestro Turbo 15" Alloys, Cruise Lights, S/S Heater Pipes, Replacement Fuel Tank. No Door Stickers. Mine since July 1986, V8 from 1991 courtesy of S&S V8 conversion kit (built not bought) and big brake kit.

saabfast · Postby **saabfast** » 12 Jan 2015 17:51

Mine is the same, folds the corners of the side 'windows'. By the looks of it the guy in the triumphtr7.com instructions has the same problem (fig 3). The only other tip which I have still not got around to is to put some material (old towel etc) over the header rail before folding the hood forward, stops the 'knobs' on the release levers scratching the windows.

Alan
Saab 9-5 2.3t Vector Auto Estate
'81 TR7 DHC

FI Spyder · Postby **FI Spyder** » 12 Jan 2015 18:32

I ran across another guy the did the towel/hood latch thing. I have the original hood and it is really tight between folding it so the fold isn't in the corner windows. Of course being 34 years old it has to be very warm out or have the help of a hair dryer to get the vinyl soft enough to make the fold right. Still looks like new though.[8D]

- - -TR7 Spider - - - 1978 Spitfire- - - - 1976 Spitfire - - 1988 Tercel 4X4 - Kali on Integra - 1991 Integra - Yellow TCT

sonscar · Postby **sonscar** » 12 Jan 2015 19:04

Looks like I am following the correct procedure as per sticker on header rail but I am not alone in that the fixed part appears to be as wide/wider than the gap between the side windows.Others also appear to have the same problem,Repeat orders for aftermarket hoods?,or is that cynical.I willjust have to be careful or not fold the hood.Thanks,Steve..

]

mine

Beans · Postby **Beans** » 12 Jan 2015 19:11

My hood is aftermarket (from S&S, 2007) and no problems there.
But ... It is essential that you manually press the centre tube down before you start folding the roof.
Also fold the side windows over the seam. And after you fold everything forward tuck the side windows nicely away under the rest of the hood.

<center>

1976 TR7 FHC (needs some TLC ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng
[url="http://www.tr7beans.blogspot.com/"]My full Blog[/url]</center>

darrellw · Postby **darrellw** » 12 Jan 2015 20:07

<blockquote id="quote">quote:<hr height="1" noshade id="quote">Originally posted by busheytrader

The best graphic about this is ironically on this website.
http://www.triumphtr7.com/documents/art ... ldroof.asp

I follow the factory / Beans instructions and have no issues. It's possible that aftermarket hoods have slightly different sized clear plastic inserts.

<hr height="1" noshade id="quote"></blockquote id="quote">

My car has the original top, still have the problem. One other thing I do sometimes is to zip down the rear window an lay it flat inside before starting to take the top down. Makes it a bit easier to manipulate the rest of the top.

-Darrell

Darrell Walker
66 TR4A IRS-SC CTC67956L
81 TR8 SATPZ458XBA406206
Vancouver, WA, USA

andyf · Postby **andyf** » 13 Jan 2015 06:55

That`s exactly what I do Darrell.

1980 Persian Aqua DHC

Anonymous

hood

hood

Who is online